Today's English article mainly introduces polypropylene, polyethylene (PE) is a thermoplastic resin produced by polymerization of ethylene.
Polyethylene odorless, non-toxic, feel like wax, has excellent low temperature resistance (minimum use temperature can reach -100~-70°C), good chemical stability, resistance to most acid and alkali erosion (not resistant to acid with oxidation properties). Insoluble in general solvents at room temperature, low water absorption, good electrical insulation.
Polyethylene can be processed in the same way as ordinary thermoplastics. It is widely used in the manufacture of films, packaging materials, containers, pipes, wire and cable, daily necessities, etc., and can be used as high frequency insulation materials for TV, radar, etc.
With the development of petrochemical industry, the production of polyethylene has developed rapidly, and the output accounts for about 1/4 of the total output of plastics. In 1983, the world's total polyethylene production capacity was 24.65 Mt, and the plant capacity under construction was 3.16 Mt. According to the latest statistics in 2011, the global production capacity reached 96 Mt, and the development trend of polyethylene production shows that production and consumption have gradually transferred to Asia, and China has increasingly become the most important consumer market.
The heat resistance of polyethylene is not high, and it is improved with the increase of relative molecular weight . Good low temperature resistance, brittle temperature can generally reach -50℃ below; And with the increase of relative molecular weight, the lowest can reach -140℃. The linear expansion coefficient of polyethylene is large, up to (20 ~ 24)×10-5/K. High thermal conductivity.
Because LDPE and HDPE have good fluidity, low processing temperature, moderate viscosity, low decomposition temperature, and do not decompose at a high temperature of 300 °C in the inert gas, it is a plastic with good processing performance. However, the viscosity of LLDPE is slightly higher, and the motor power needs to be increased by 20% to 30%; It is easy to break the melt, so it is necessary to increase the die gap and add processing AIDS. The processing temperature is slightly higher, up to 200 ~ 215℃. Polyethylene has low water absorption and does not need to be dried before processing.
Polyethylene products are easy to crystallize during cooling, so pay attention to mold temperature during processing. To control the crystallinity of the product, so that it has different properties. The molding shrinkage of polyethylene is large, which must be considered when designing molds.
Giới thiệu về cảng Ninh BaJune 30, 2022Tiền Thân của cảng Ninh ba là cảng vụ Ninh ba. Cảng Ninh Ba bao gồm khu vực cảng beilun, khu vực cảng zhenhai, khu vực cảng Ninh Ba, khu vực cảng daxie và khu vực cảng chuanshan. Nó là một đa chức năng...view
Tại sao mùa đông lại tệ cho việc xây dựng lớp phủJune 30, 20221. Vấn đề lưu trữ và vận chuyển đối với lớp phủ chất lỏng, sẽ có vấn đề về điểm nóng chảy, Miền Bắc Trung Quốc vào tháng 11 Về cơ bản đã giảm xuống dưới điểm đóng băng, rõ ràng là trong trường hợp này,...view
Pháp Luật hỗ trợ Nền Kinh Tế tuần hoànJune 30, 2022Nền Kinh Tế tuần hoàn đã nhận được sự hỗ trợ cụ thể từ chính phủ Đức, Nhật Bản, Trung Quốc và Liên minh Châu Âu. Đức là quốc gia Châu Âu đầu tiên thông qua luật pháp quốc gia để giảm...view